TPD-Compliant Pod Systems: What EU Buyers Must Specify

· CigGo — Shenzhen Dorteam Technology Co., Ltd.

What "TPD-compliant" means in practice

The EU Tobacco Products Directive (2014/40/EU), as implemented by each member state, sets the rules that shape every pod system sold in the EU. For hardware buyers the important ones are:

  • Pod capacity: a maximum of 2 ml for a pod, tank or cartridge.
  • Nicotine strength: a maximum of 20 mg/ml.
  • Child-resistant and tamper-evident: the refill mechanism and the packaging must meet both requirements.
  • Notification: the manufacturer or importer must notify the competent authority of each member state before placing the product on the market, with product and ingredient information.
  • Labelling and warnings: prescribed health warnings, ingredient list, and batch identification.
  • Ingredient reporting: annual reporting on ingredients and emissions, including toxicological data where required.

The UK applies the same core limits through TRPR, with its own notification route. Several member states add national rules on flavours, advertising, distance selling or packaging, so the EU baseline is a floor, not the whole file.

This guide is written for hardware buyers and is not legal advice. The economic operator placing the product on the market is responsible for the notification and for verifying national rules.

What the 2 ml ceiling does to a pod design

Two millilitres is a small number, and it propagates through the whole design.

Usable fill versus nominal capacity. A pod labelled 2 ml may contain less usable liquid once headspace, the fill port and the coil chamber are accounted for. Buyers should ask for both the nominal capacity and the usable fill, and confirm how the figure is measured.

Coil area and session length. With less liquid, the coil must be matched so the session is satisfying without running dry at the end of the fill. A 1.8 ml pod with a 1.0 Ω ceramic coil behaves differently from a 2.0 ml pod with a 0.5 Ω coil, even if both fit the cap.

Fill port geometry. A refillable pod must be fillable without overfilling, and the fill port must be child-resistant where the rules require it. That usually means a specific port design and a sealing method, not just a smaller tank.

Leak margin. A smaller fill leaves less tolerance for overfill and temperature swings, so the seal and the fill protocol become more important, not less.

Closed versus refillable under TPD

Both architectures can comply, but they carry different obligations.

A closed pod is prefilled and sealed at the factory. The pod is the unit that must meet the 2 ml cap, and the factory controls the fill volume, flavour and batch record. The notification covers the pod and the device as placed on the market.

A refillable pod ships empty or fillable, and the user adds liquid. The device and the pod must meet the hardware requirements, while the liquid is a separate product with its own notification and labelling obligations. That separation can simplify some questions and complicate others — in particular, which operator is responsible for the liquid's notification and how the refill instructions are worded.

For a buyer, the practical question is who owns the compliance file. If you are importing a closed pod, the factory's fill records and the importer's notification are tightly linked. If you are importing a refillable device and selling your own liquid, you need both the device documentation and your own liquid notification.

The documents to collect before ordering

A TPD submission is only as good as the file behind it. Ask the supplier for:

Document Why it matters
Technical specification sheet Defines capacity, resistance, materials and dimensions that the notification will quote
Material declarations Supports the ingredient and material questions in the file
Test reports (where applicable) Evidence for child-resistance, tamper-evidence and electrical safety claims
Quality certificate ISO 13485 or equivalent QMS evidence
Batch/lot convention Ties production records to the notified product
Packaging artwork with warnings Confirms the label matches the notification
Refill instructions Required where the product is refillable

If a supplier cannot provide a specification sheet that matches the artwork and the samples, stop. Mismatches between the notified specification and the shipped product are one of the most common causes of enforcement problems.

Engineering a pod that survives the 2 ml review

The design choices that make a pod TPD-ready are mostly unglamorous:

  • Capacity tolerance. Agree how fill volume is measured, at what temperature, and with what acceptable range. A pod that can be filled to 2.2 ml "by accident" is a compliance risk even if the label says 2 ml.
  • Child-resistant fill and packaging. The mechanism has to work in normal use, not just on a lab bench. Test it with users, not only with a checklist.
  • Tamper evidence. Decide whether it is on the pod, the retail box or both, and make sure the artwork matches.
  • Leak and overfill behaviour. Test at the top of the fill range and after temperature cycling, not only at nominal fill.
  • Compatibility with the notified liquid. If the liquid changes viscosity between batches, the coil specification may stop delivering the expected session.

Where the CigGo platforms sit

CigGo's pod platforms are specified per project, so the TPD configuration is chosen at the brief stage rather than retrofitted. For 2 ml markets, the closed options include the M20 closed pod system with 1.8 ml prefilled pods at 0.6 Ω, the M21 with 2.0 ml pods and pod-connection vibration feedback, and the M28 Bysoul-ii with 1.8 ml pods at 0.5 Ω. All three share a 450 mAh rechargeable device with Type-C charging.

On the refillable side, the M22 Refillable Pod System uses 1.8 ml food-grade PCTG pods with a ceramic 1.0 Ω coil, and can be supplied with empty or factory-prefilled pods. That 1.8 ml nominal capacity leaves headroom under the 2 ml ceiling.

The Bysoul M23 open pod system is a 2.5 ml refillable pod. That capacity is above the TPD ceiling, so the M23 is positioned for markets without a 2 ml cap; it is not the platform to specify for an EU launch unless the pod is resized for that project. Being explicit about that is part of a good supplier conversation.

The full family, including the higher-output M37 Bysoul, is listed on the pod system hub. The TPD compliance overview covers the regulation itself, and the certifications page explains the ISO 13485 and CE/RoHS documentation available on request.

A TPD launch checklist for buyers

  1. Confirm the destination member state and its national additions to the TPD baseline.
  2. Fix the pod capacity at or below 2 ml, with a documented usable fill.
  3. Decide closed or refillable, and name the economic operator responsible for notification.
  4. Collect the specification sheet, material declarations and artwork before tooling.
  5. Agree the fill-volume tolerance and the leak test method in writing.
  6. Test child-resistance and tamper-evidence with real users.
  7. Confirm who files the notification and which documents they need from the factory.
  8. Re-check the artwork after the notification, not before.
  9. Keep batch records traceable from production to the notified product.
  10. Re-test if the liquid, coil or pod capacity changes.

Frequently asked questions

Is a 2.5 ml pod TPD compliant?

No. The TPD cap is 2 ml, so a 2.5 ml pod such as the Bysoul M23 is not compliant for an EU launch unless the pod is resized for that project. It suits markets without a 2 ml ceiling.

Does TPD require the pod to be child-resistant, or only the packaging?

The refill mechanism and the packaging must both meet the child-resistant and tamper-evident requirements where they apply. In practice that means the fill port design and the retail packaging both need testing, not just one of them.

Can a refillable pod be TPD compliant?

Yes, provided the device and pod meet the hardware requirements and the liquid has its own notification and labelling. The 1.8 ml M22 Refillable pod sits under the 2 ml cap; the compliance file must cover both the hardware and the liquid.

Who files the TPD notification?

The manufacturer or importer placing the product on the market in that member state. If you are the importer, you are normally the responsible operator; confirm the division of responsibilities with the factory before ordering.

Which CigGo pod is best for an EU launch?

For a closed model, the 1.8 ml M20 or M28 and the 2.0 ml M21 are the closest fit. For a refillable model, the 1.8 ml M22 Refillable Pod System fits under the cap. The final specification is confirmed per project with the destination market.

Ask before you tool

Send the destination market, the capacity you plan to declare and the liquid you intend to sell through the inquiry form. Sales will confirm which platform fits and which documents the notification will need.