CBD Pod Systems: Open vs Closed Hardware
Cannabis oil is not e-liquid
Most pod-system advice is written for nicotine e-liquid: a 50/50 or 60/40 blend that wets a cotton wick reliably and behaves predictably across a temperature range. Cannabis oil — distillate, live resin, rosin or a formulated vape oil — is a different material. It is more viscous, it can crystallise or separate, and its response to heat is different. A device that works well for nicotine can produce dry hits, blocked flow or a burnt note when the same coil meets a thick oil.
That is why CBD pod systems are usually specified around the oil first and the shell second. The parts that change are the tank (often postless and ceramic), the fill path, the coil specification, and sometimes the preheat behaviour. This guide compares the two hardware routes — open (refillable) and closed (prefilled) — and the CigGo devices that fit each.
How cannabis oil changes the hardware
Four material properties drive most of the design:
Viscosity. A thicker oil needs more heat and a larger flow path to reach the coil. A thinner oil can flood a coil designed for distillate. The coil specification should be chosen against the actual oil, not a generic "for CBD" label.
Crystallisation and separation. Some oils change consistency over time or in cold storage. A tank that lets the user see the oil — glass or clear PCTG — makes the change visible before it becomes a bad puff.
Terpene and flavour chemistry. Terpenes are volatile, and a coil that runs too hot can strip the flavour profile. Temperature control and a ceramic element usually give a gentler heat than a bare wire coil.
Potency and dose control. A device that delivers a consistent dose per draw matters commercially as well as technically. Preheating and voltage selection help, but the oil and the coil have to be matched.
Ceramic and postless: why they matter
A conventional cartridge uses a central post and a cotton wick. A postless tank removes the post, which increases usable volume and shortens the path the oil travels to the coil. Paired with a ceramic element, it gives more uniform heating for thick oils and reduces the chance of a dry, metallic note when the coil is starved.
The visible-tank design follows from the same logic: if the user can see the oil, they can see when it is running low, when it has separated, or when the device needs a preheat. On screen devices, the display adds battery and flavour feedback, which is useful when the same device carries two different oils.
Open versus closed CBD pods
The architecture question is the same as in nicotine pods, but the trade-offs shift.
A closed CBD pod is prefilled and sealed at the factory. The oil is part of the product, the fill volume is fixed, and the user replaces the pod. This suits brands that sell a finished oil product and want consistency, tamper evidence and a simple retail story. The manufacturer controls the fill, so leak behaviour and dose consistency are factory variables rather than user variables.
An open CBD pod has a fill port and the user — or the brand's customer — supplies the oil. This suits oil brands whose customers already buy bottles, and markets where a small fill volume is preferred. The trade-offs are the same as in nicotine: fill quality moves into the user's hands, and the device must tolerate a range of oil viscosities.
A third route is a sealed dual-chamber device that carries two oils in one unit without a pod interface at all. That is effectively a closed system with two independent tanks, and it is useful when a brand wants to sell a day/night pair or two formulations in one SKU.
The CigGo devices for each route
CigGo builds CBD hardware on the same pod and tank platforms as the rest of the range, specified for oil rather than e-liquid.
For a closed, dual-chamber format, the M60 Opod dual-flavor CBD vape carries 1 ml + 1 ml glass tanks with a ceramic core, a 400 mAh rechargeable battery, Type-C charging and selectable output voltages (2.2–2.8 V). It is specified as optimised for diamond oil, and the two chambers can carry two formulations without mixing.
For a disposable, sealed CBD device, the J90 dual-tank CBD vape uses 1 ml + 1 ml tanks with dual ceramic coils at 1.3 Ω, a 400 mAh rechargeable cell and a 1.8″ screen that shows battery level and the active flavour. The J91 scales the same idea to 2 ml + 2 ml with a 450 mAh cell. Both are sealed devices: the oil ships inside, and the unit is replaced when it is empty.
For an open pod, the M22 Refillable Pod System can be specified with empty pods for oil fills, subject to compatibility testing with the oil being used. Its 1.8 ml PCTG pod and ceramic 1.0 Ω coil are a starting point, not a guarantee — the oil sample decides. The Bysoul M23 open pod system offers a 2.5 ml pod with 0.8 Ω or 0.6 Ω options for markets without a 2 ml cap.
The CBD vape hub lists the full family, including the J92 and J93, and the pod system hub covers the open and closed pod platforms in more detail.
Filling, leak behaviour and the first puff
The practical failure modes in CBD hardware are different from nicotine:
- Overfill. A thick oil that expands with heat can overflow a tank filled to the brim. The fill line matters more than the nominal capacity.
- Cold start. A cold oil may not flow for the first few draws. Preheat or a short warm-up cycle prevents a dry first puff.
- Long storage. A half-full tank can change consistency over weeks. Visible tanks and small fills reduce the risk.
- Cleaning. Some oils leave residue that affects the next fill. The device should be replaceable at the pod or tank level, not cleaned like a bottle.
For a closed product, these become factory questions: fill volume, headspace, storage testing and pod sealing. For an open product, they become user instructions, and the quality of those instructions is part of the product.
Compliance and market questions
Cannabis and CBD rules vary by country and, in federal systems, by state: licensing, potency limits, packaging and labelling, and in some cases device certification. CigGo supplies the hardware and manufacturing documentation; it does not supply the oil and does not authorise a market. Buyers should confirm the device specification against their own market's requirements before ordering, and name the operator responsible for the oil's compliance.
For nicotine-adjacent hardware questions, the TPD guide covers the 2 ml and 20 mg/ml framework. CBD and cannabis devices usually sit under a separate regime, so do not assume the TPD file covers them.
Open versus closed: a quick decision table
| If this is true | Route |
|---|---|
| You sell a finished oil product and want a sealed retail SKU | Closed pod or sealed dual-tank |
| Your customers already buy bottles and want to fill their own pod | Open pod |
| You need two formulations in one device without mixing | Dual-chamber closed device |
| Your market caps fill volume and you want top-up flexibility | Open pod with a small pod |
| You cannot support customers through a filling routine | Closed pod |
| You want visible oil and screen feedback | Dual-tank sealed device (J90/J91) |
A buyer checklist for CBD hardware
- Send an oil sample and the intended dose per session before choosing a coil.
- Confirm the tank material and whether the oil is compatible with PCTG or needs glass.
- Agree the fill volume, headspace and storage test conditions.
- Decide open or closed, and who fills the pod.
- Confirm the preheat or voltage range and the first-puff behaviour.
- Agree the leak test method and acceptance criteria.
- Confirm which compliance documents the destination market needs.
- Ask for empty and prefilled sample pods where available, and test both.
Frequently asked questions
Can the M22 Refillable pod be used with CBD oil?
It can be specified with empty pods for oil fills, but compatibility depends on the oil. Viscosity and formulation should be tested with a sample before ordering; the 1.0 Ω ceramic coil is a starting point, not a universal answer.
What is the difference between a CBD pod and a CBD disposable?
A pod system keeps the battery and replaces the pod; a disposable CBD device seals battery, coil and oil in one unit that is discarded when empty. Pods are better for repeat purchase and lower waste; disposables are simpler to sell and use.
Why do CBD devices use ceramic coils?
Ceramic elements heat more evenly than a bare wire coil and are less prone to hot spots with thick oils. Combined with a postless tank, they improve flow and reduce the dry, metallic note that a starved wick can produce.
Can one device carry two different oils?
Yes, if it has two independent chambers. The M60 Opod carries 1 ml + 1 ml glass tanks with separate ceramic cores, and the J90/J91 dual-tank disposables carry two oils with separate coils, so the formulations do not mix.
Do you supply the oil or only the hardware?
CigGo supplies hardware and manufacturing documentation, not the oil. The oil, its compliance and its market authorisation remain with the brand or importer.
Next step
Send the oil sample and the target market through the inquiry form — sales will confirm the tank material, coil specification and fill route, and quote samples before any tooling decision.